Hi,
Would it be possible to combine the Bolt with a BigQuad deck to allow for more connections of external peripherals? Such as GPS, I2c, etc
Search found 28 matches
- Sat Nov 06, 2021 9:58 pm
- Forum: Developer Discussions
- Topic: Possible to combine Bolt and BQ Deck?
- Replies: 1
- Views: 1050
- Fri Nov 05, 2021 10:26 pm
- Forum: Developer discussions
- Topic: [RESOLVED] DSHOT For BigQuad Deck
- Replies: 4
- Views: 14978
Re: [RESOLVED] DSHOT For BigQuad Deck
Not to revive an old thread. But the BQ deck and Bolt have by now received support for Oneshot125 and Oneshot42. Does this mean that they could also receive support for Multishot? I don't believe that it requires DMA, and the timings should be well within the processor capability. It would also prob...
- Thu Nov 04, 2021 8:54 pm
- Forum: General discussions
- Topic: What is the connector opposite the uUSB on the CF Bolt?
- Replies: 4
- Views: 1104
Re: What is the connector opposite the uUSB on the CF Bolt?
Tobias,
I'd need to use the motor signal wires to send signals to the motors. Would soldering GND and VBAT where the XT60 connector was provide information to the Bolt about voltage?
I'd need to use the motor signal wires to send signals to the motors. Would soldering GND and VBAT where the XT60 connector was provide information to the Bolt about voltage?
- Wed Nov 03, 2021 7:08 pm
- Forum: General discussions
- Topic: What is the connector opposite the uUSB on the CF Bolt?
- Replies: 4
- Views: 1104
Re: What is the connector opposite the uUSB on the CF Bolt?
Also, what is the best method for connecting the Bolt to an external PDB? Ideally there'd be some sort of data link between the two so that I could read power usage and battery information. Is that something that's possible?
- Wed Nov 03, 2021 6:31 pm
- Forum: General discussions
- Topic: What is the connector opposite the uUSB on the CF Bolt?
- Replies: 4
- Views: 1104
What is the connector opposite the uUSB on the CF Bolt?
On the Crazyflie Bolt, on the other side of the board from the uUSB, there is a 6-pin female connector, labeled in the datasheet as P3. What is this connector for? Can it be used to connect the Bolt to an external PDB?
- Tue Nov 02, 2021 12:45 am
- Forum: General discussions
- Topic: Extending range with Crazyflie Bolt
- Replies: 1
- Views: 10251
Extending range with Crazyflie Bolt
Hi, I'm working with a CF Bolt and a Crazyradio PA, and I'd like my drone to be able to operate at longer ranges than the rated 1km. Would it be possible to wire up "proper" antennas to the CF Bolt, or to increase the signal strength of the Crazyradio PA? Possibly both? The goal is to exte...
- Tue May 12, 2015 5:42 pm
- Forum: Support
- Topic: Crazyflie 2.0 tilts left at takeoff [SOLVED]
- Replies: 1
- Views: 1935
Re: Crazyflie 2.0 tilts left at takeoff
Never mind, never mind. Turns out the props were in the opposite spots. Just for future reference, https://wiki.bitcraze.io/projects:crazy ... e:assembly shows you how to fix it. Right down near the bottom.
- Mon May 11, 2015 11:48 pm
- Forum: Support
- Topic: Crazyflie 2.0 tilts left at takeoff [SOLVED]
- Replies: 1
- Views: 1935
Crazyflie 2.0 tilts left at takeoff [SOLVED]
I have a CF2. It has been flying fine for the past week or so. A few days ago, I turned it on and connected it to the VM. As soon as I increased the thrust to a slight launch, the CF2 wants to go left. The more thrust, the further left it goes. At around 60% thrust or so, it flips(to the left, of co...
- Tue May 05, 2015 3:13 am
- Forum: Developer Discussions
- Topic: Programmable Flight Demonstration
- Replies: 11
- Views: 8820
Re: Programmable Flight Demonstration
I have the same problem as BlitzProgrammer: the program can't find the log module. Feedback: Traceback (most recent call last): File "escape.py", line 34, in <module> from cfclient.utils.logconfigreader import LogConfig ImportError: No module named cfclient.utils.logconfigreader How do I f...
- Sat Apr 25, 2015 6:34 pm
- Forum: Support
- Topic: CrazyFlie altitude hold problem
- Replies: 13
- Views: 11158
Re: CrazyFlie altitude hold problem
Yes to both. I am using the VM, and I see the altHold in the Parameters tab. I run the update script once a week, so I trust that they are the most recent versions. I am running this on my MacBook Air 2014 with VirtualBox. I am also using a Sony PS3 controller and the Crazyradio PA